This post is also available in:
Deutsch (German)
Overview
CODA Audio strives to provide complete solutions that allow for simple, setup, integration and operation of CODA Audio systems. The LINUS T-RACK is an important part of this effort. The T-RACK houses three LINUS14D amplifiers in an efficient road ready package. This factory-made standard includes switchable rear mounted power distribution, shock mounted infrastructure and ready-to-fly integrated rigging hardware that allow it to be used almost anywhere. The T-RACK’s simplified front mounted connectivity and effortless expandability make it easy to use.
Specification
| GENERAL |
| Components |
3x LINUS14D
1x PAN-T Connecting Panel
1x PDU-T Power Distribution Unit
1x enclosure with integrated rigging hardware (2-point), shock mount suspension system, sliding doors on front and rear side, protection grille on the rear side |
| Connecting panel front side |
PAN-T
Powered connecting panel including two ethernet switches (one for Ethernet and one for Dante) and integrated cabling system |
| Analog |
4x XLR Input
1x etherCON® analog Input/ Link |
| LINET (AES/EBU) |
1x etherCON® Input (8x signal channels)
1x etherCON® Output (8x signal channels) |
| Dante |
1x etherCON® |
| Remote Control |
1x etherCON® Input
1x etherCON® Output
Recessed push button to select AES over Ethernet signal input
AES over Ethernet activated (Blue LED): Transport of remote control incl. 4x LINET (AES/EBU) signal channels on ETHERNET marked etherCON® connectors enabled. PRIM = Input / SEC = Link
LINET activated (Orange LED): LINET signal and remote control sockets seperated |
| Outputs |
6x Neutrik NL4 speakON®
3x Neutrik NL8 speakON®
Output section can be extended with the PAN-MP Multipin connection panel
3x LKS 19 (8x Output channels per connector for two combined LINUS T-RACKS) |
| Sensor Control Connection |
6x XLR5 |
| Optional |
PAN-MP
Output Section can be extended with the PAN-MP Multipin connection panel
3x LKS 19 (8x Output channels per connector for two combined LINUS T-RACKS) |
| Power distribution unit rear side |
PDU-T
Power distribution unit with integrated cabling system for amplifiers and connecting panel operated in EU |
| AC input |
CEE 32A 230/400V/5P |
| AC link |
CEE 32A /400V/5P
Type F 16A Schuko female outlet protected by a C16 circuit breaker (incl. PAN-T) |
| Optional power distribution unit for operation in EU and US |
PDU-T INT
Power distribution unit with integrated cabling system for amplifiers and connecting panel operated in EU and US |
| AC input |
EU: CEE 32A 230/400V/5P
US: L21-30 120/208V
Power inlet switchable on the backside of the power distribution unit |
| AC link |
CEE 32A/400V/5P
EU: Type F 16A Schuko female outlet
US: 5-15 female outlet
Both protected by a 10A/1P circuit breaker (incl. PAN-T) |
| Physical |
|
| Enclosure material |
Birch plywood |
| Finish |
Polyurea coating |
| Dimensions (WxHxD) |
607 x 547.4 x 650 mm / 23.9” x 21.55” x 25.59” |
| Shipping dim. (WxHxD) |
627 x 567.4 x 670 mm (0.238 m³) / 24.69” x 22.34” x 26.38” |
| Net weight |
93 kg / 205.03 lbs. |
| Shipping weight |
96 kg / 211.64 lbs.
Volume = 0.238 m³ / 8.405 ft³ |
* Typical values – some variation may exist due to component tolerances.
**Voltage range should not be exceeded. Amplifier output power performance will degrade below nominal voltage & increase above nominal voltage.
