The LINUS-V908 is an eight-channel touring-grade power amplifier based on CODA Audio’s latest amplifier topology. Designed in a compact 2U format, it provides high power density and very low distortion performance, ensuring accurate and reliable audio reproduction in professional touring and portable system applications.
The V908 delivers 1500 W at 2 ohms per channel across eight channels. Channels can be bridged independently, allowing flexible output configurations of 1500 W at 4 ohms or 3000 W at 4 ohms, enabling efficient system scaling and configuration flexibility.
The amplifier incorporates a new DSP architecture, supporting future firmware updates and long-term adaptability.
Dual high-efficiency SMPS with power factor correction (PFC) allows operation across a 100–240 V mains voltage range.
Analogue and LiNET inputs are provided as standard, with Dante connectivity available on the V908-D model.
Factory presets for CODA loudspeakers—excluding sensor-controlled subwoofers and large-format line arrays—are stored internally and accessed via the 320 × 240 pixel touchscreen. Control is available locally, via the LINUS Control App for individual amplifiers, or through networked operation using LINUS Control Software for full system management.
The LINUS-V908 is engineered for touring reliability and is covered by a five-year guarantee. Ongoing firmware updates ensure continued compatibility, updated presets and specialist functionality.
Power that punches above its size. Control that fits in your pocket.
Signal-to-noice ratio
(22 Hz – 20 kHz, 4 Ω – digital input)
>113 dB (unweighted)
>116 dB (A-weighted)
Frequency response
(8 Ω load with CLEAR preset)
20 Hz – 20 kHz = (+0.3 dB /-0.2 dB)
THD+N & IMD
(4 Ω load @ 1/2 output power)
20 Hz – 20 kHz = < 0.05%
Latency
(input to loudspeaker output)
Minimum 2.70 ms AES/EBU input
Minimum 2.00 ms analog input
Protection circuits
Inrush current limiter
Thermal limiter
Output DC
SMPS over-current
Output overload
User interface
IPS Touchscreen 240×320
Mute / Status / Limit / Signal / Protection / Ethernet / Power on / Mains voltage
Front panel control of audio parameters: Preset / Delay / Mute / Snapshot / Standby
Ethernet connection
2 × 100 Mbps RJ45 Control (1 port accepts PoE 802.3af backup power for DSP)
2 × 1000 Mbps RJ45 Dante™ (Redundant)
AC Mains
AC mains
32A powerCON®
AC mains input connector
100 V – 240 V AC with PFC
AC mains voltage (nominal)**
90 V – 264 V AC
AC mains voltage (maximum)**
Amplifier in standby = 16 W Amplifier idle = 40 W Amplifier ¼ power = 3000 W
AC mains frequency
47 – 63 Hz
Input
Input sources
Analog & LINET & DANTE™ (optional)
Analogue input impedance
(balanced)
20 kΩ
Maximum input level (analogue differential)
+21 dBu
Input connections
8 × XLR Female 1 × RJ45 LINET IN (8 × CH) 1 × RJ45 LINET LINK (8 × CH) 2 × RJ45 DANTE IN (8 × CH) (optional)
1000 W @ 8 Ω 1600 W @ 4 Ω 3000 W @ 2 Ω 3200 W @ 8 Ω bridged 6000 W @ 4 Ω bridged
Maximum output voltage*
+/- 90 V pk
+/- 160 pk (bridge)
Maximum output current*
+/- 40 A pk
Damping Factor
(8 Ω load, 1 kHz & below)
>2500
Minimum output load
2 Ω per channel
4 Ω in bridged mode
Power output connections
4 × SpeakON® 4 pole
Thermal
Operating temperature
+5°C to +55°C
41°F to 131°F
Thermal output
(BTU/h)
TBD
Thermal output
(kWh)
TBD
Cooling
2 × thermally controlled fans. Hot air expelled at rear.
Physical
Dimensions (WxHxD)
483.5 x 88 x 454.18 mm / 19” x 3.4” x 17.8” (2U)
Shipping Dim. (WxHxD)
675 x 130 x 560 mm (0.049 m³) / 26.5” x 5.1” x 22”
Net Weight
12 kg / 26.46 lbs.
Shipping weight
14.75 kg / 32.52 lbs.
* Typical values – some variation may exist due to component tolerances.
**Voltage range should not be exceeded. Amplifier output power performance will degrade below nominal voltage & increase above nominal voltage.
We use cookies to ensure that we give you the best experience on our website. If you continue to use this site we will assume that you are happy with it.OkRead more
